News & Post Archive

HK P30, P2000 Short Reset System

By Steve McGough / December 31, 2018

Replicate our custom in-house short reset conversion with a drop-in kit for your HK P2000 or P30 without a thumb safety. Cut from bar stock steel, these kits provide an exacting fit for easy install.

The kit shortens the reset travel distance by about one-third, reduces trigger over-travel and reduces pull weight while maintaining all factory safety functions.

This kit is specific to the HK P2000 and P30 models without a thumb safety, including DA/SA and LEM variations. Review our Fit Guide below.

The parts provided – control latch, extended sear roll pin and firing pin block spring – are designed to be installed together as a complete system.

Read More

HK USP, HK45 Short Reset System

By Steve McGough / December 24, 2018

Our Short Reset System for the HK USP and HK45 replicates the short reset conversion available in our in-house custom action work. Cut from bar stock steel, these kits provide an exacting fit for easy install.

The kit shortens the reset travel distance by about one-third, reduces trigger over-travel and reduces pull weight while maintaining all factory safety functions.

This kit is specific to the HK USP and HK45 models with or without a thumb safety, including DA/SA and LEM variations. Review our Fit Guide below.

The parts provided – control catch, pin and spring – are designed to be installed together as a complete system.

Read More

HK P30 (with Safety) Short Reset System

By Steve McGough / December 24, 2018

Replicate our custom in-house short reset conversion with a drop-in kit for your HK P30 with thumb safety. Cut from bar stock steel, these kits provide an exacting fit for easy install.

The kit shortens the reset travel distance by about one-third, reduces trigger over-travel and reduces pull weight while maintaining all factory safety functions.

This kit is specific to the HK P30 model with a thumb safety, including DA/SA and LEM variations. Review our Fit Guide below.

The parts provided – control latch, extended sear roll pin and firing pin block spring – are designed to be installed together as a complete system.

Read More

P320 Inner Base Plate – Square Peg

By Steve McGough / December 13, 2018

If you’ve purchased – or would like to purchase –  our SIG Suaer® P320 Hard Duty Base Pads, and have the old style inner base plate with the round peg, you’ll need these inner base plates with the square peg. Installation is easy, and requires no special tools.

Read More

Hard Duty Use SIG P226 Magazine Base Pads

By Steve McGough / November 24, 2018

Looking for hard duty replacement base pads for your SIG Sauer® P226 magazines?

These custom Grayguns hard duty use pads have been built for military and law enforcement applications. Designed by Mike Grasso and tested by our LE Team to be repeatedly dropped on concrete or asphalt hundreds of times, they are a perfect upgrade for plastic base pads.

Two versions available.

  • Hard Duty Base Pad for OEM SIG Sauer P226 Magazines
  • Hard Duty Base Pad for Mec-Gar P226 Magazines

Also appropriate for competition and shooting enthusiasts looking for a quality, durable upgrade.

Discount available when you buy three or more base pads! ($15 each instead of $18 each.) The discount is shown in the cart prior to checkout.

Read More

P365 Straight Trigger

By Steve McGough / November 23, 2018

Apologies. We are currently out-of-stock. We’re sorry for the inconvenience. Rest assured we want to get a trigger to you! We’re working hard and more are in the pipeline. 

The Grayguns straight trigger for the SIG Sauer® P365 is a drop-in, bar-stock, enhanced trigger for your P365. Our P365ST Straight Trigger optimizes the length of pull and decreases excess over-travel, while keeping the toe of the trigger in the same location as the stock, curved trigger.

The trigger breaks at 90 degrees giving the operator a clean index while providing a wider area of finger placement.

Due to increased demand, limit one (1) trigger per customer.

Read More

SIG Sauer P320 Armorer’s Block

By Steve McGough / October 12, 2018

Limited edition custom armorer’s block for the SIG Sauer® P320. Designed by the team at Grayguns to assist qualified armorers when upgrading components, adding spring kits and completing work on the striker assembly.

Facilitates disassembly and assembly of the P320’s fire control unit (FCU). Two-sided to allow for removal and installation of one-way pins in the FCU.

Read More

EDC Straight Optimized Trigger System for SIG P-Series

By Steve McGough / October 7, 2018

Specifically designed for the SIG Sauer® classic P-Series DA/SA pistols (not DAO/DAK). The Enhanced Daily Carry (EDC) with Straight Optimized Trigger (SOT) reduces DA and SA pull weights with dramatically improved pull characteristics.

This system consists of our new SOT mated to a enhanced, custom-designed trigger bar.

Two Versions

  • For SIG Sauer P226, P229 and P228 DA/SA pistols with DAK compatible frame window cut
  • For SIG Sauer P226, P229 and P228 DA/SA pistols with non-DAK compatible frame window cut

Ensure you read the detailed description below to order the correct version.

Read More

Hard Duty Use SIG P320 Magazine Base Pads

By Steve McGough / July 19, 2018

Looking for Hard Duty Use replacement base pads for your SIG Sauer® P320?

These custom Grayguns HDU pads have been built for military and law enforcement use. Designed by Mike Grasso and our LE Team to be repeatedly dropped on concrete or asphalt hundreds of times, they are a perfect upgrade for the OEM plastic base pads.

Also appropriate for competition and shooting enthusiasts looking for a quality, durable upgrade.

Backwards compatible with all versions of P320 modules, including the standard and xSeries with or without the extended magwell installed.

Two versions available

  • Standard Version – Designed for the XSeries without the magwell. Also works with the P320 module.
  • Extended Magwell Version – Designed for the full-size magazine in a XSeries with the magwell. Also works with 21-round magazines and fits the standard P320.

Base pads are compatible with new SIG P320 magazines with the square pegsDo you have the base plates with the round peg? If yes, you’ll need to purchase a P320 Inner Base Plate – Square Peg for each of your magazines.

Discount available when you buy three or more base pads! ($15 each instead of $18 each.) The discount is shown in the cart prior to checkout.

Read More

Custom AIWB Holster

By Steve McGough / May 29, 2018

This appendix inside-the-waistband holster is available for the SIG Sauer® P320, XSeries, P365, P320, P226, P229 and P228.

Custom holster from Grayguns for those looking for a high-quality, custom-designed Kydex® appendix inside-the-waistband holster.

This custom-designed holster a collaboration between PHLster Holster, Henry Holsters and Mike Grasso from Grayguns.

Please read our return policy, which applies to holsters just like any other product.

Read More