SIG P-Series Dual Adjustable Straight Trigger
$69.00
Machined from tough steel, the SIG P-Series Dual Adjustable Straight Trigger includes over travel and pre-travel adjustability. Ensure you review the full description prior to ordering. (Scroll down for video introduction.)
Heat treated and finished in black oxide or Nickel Teflon® PTFE. Ensure you review the full description prior to ordering.
The trigger is designed to fit both current and older model traditional double action (DA/SA/de-cocker) P-Series pistols. See the complete fit guide and description below.
Description
The SIG P-Series Dual Adjustable Straight Trigger is the straight-faced version of our legendary curved P-Series Dual Adjustable Trigger. This trigger includes over travel and pre-travel adjustability. (Adjustable for double action slack and single action over travel.)
The optimized trigger face pressure-wall angle provides for outstanding single action sear release and positive, ultra-fast reset control. The ergonomics provides superior double action leverage and control.
Dual Adjustable Straight Trigger Details
This steel trigger is carefully heat treated and finished in black oxide or Nickel Teflon PTFE. Tight pin hole tolerances assure smooth, solid function. Guaranteed for life against defects in materials or workmanship.
Made with love, supplied with a hex key.
The trigger weight is about .83 ounces (23.45 grams)
Fit Guide
The trigger is designed to fit both current and older model traditional double action (DA/SA/decocker) P-Series pistols, including
- X5 All-Round
- P220 (see exceptions below)
- P226
- P228
- P229
- P227 and others
These triggers are approximately 10mm wide. At this time, we are not suggesting this trigger for guns equipped with the DAK trigger system.
This trigger may not be fully compatible with California compliant or similar P-series pistol models equipped with a magazine disconnector, and Grayguns urges caution. We do not recommend deactivating any mechanical safety device.
The Grayguns DA/SA triggers will not fit SIG Pro, P225 / P6, P239, West German P220s, or most SAO models. Most of these triggers are a narrower 8mm width.
If you’re looking for the single action only (SAO) version of this trigger, check out the P-Series SAO Dual Adjustable Straight Trigger.
Disclaimer
These parts are intended for installation by a qualified armourer or gunsmith. In some cases professional fitting will be required by a trained, qualified armorer/gunsmith who is very familiar with the pistol’s action. This is due to the varying tolerances present in all mass-produced firearms. Although kits fit with no issues in a great majority of pistols, Grayguns is unable to guaranty perfect functionality in every instance. Grayguns does offer installation services for all parts kits we offer.
Additional information
| Variation | Black Oxide, Dual Adjustable Straight Trigger (SAO with Pin), Dual Adjustable Straight Trigger (SAO without Pin), Nickel Teflon |
|---|
Share your thoughts!
Let us know what you think...
Only logged in customers who have purchased this product may leave a review. Log in now
petrucci.steven (verified owner) –
This is a great trigger. I always seem to shoot better with a flat trigger and this is no exception. It’s easy to install as well. If I have to say anything negative it’s that there seems to be a little bit of a side to side wobble to it.
(1) (0) Watch Unwatch
juanmotorcop (verified owner) –
this trigger is great., fit and function is better than factory part, and feels much crisper.
(1) (0) Watch Unwatch
mdstahoe (verified owner) –
I installed this trigger, along with Sig’s SRT Kit, and they made my P227 a whole new gun. Installation was easy and the trigger dropped right in with no fitting. Great part if you’re looking for an easy and inexpensive upgrade. Would definitely recommend and buy again.
(1) (0) Watch Unwatch
mattdevi (verified owner) –
If you can remove and install the trigger bar, you can install this trigger.
For me, there was a dearth of online information about how to adjust the DA pre-travel but the SA over travel was covered such that I set that when I installed the trigger.
I then went back and adjusted the DA pre-travel to only have about 1/8″ of movement with 100% DA reset function.
For my big hands, I have more room for my trigger finger in the trigger guard after installing the P22xST.
I installed the trigger in a P220R with a SIG SRT and will order another one for my P226R along with a GG SRT when they become available.
I have a GG P-series spring set on order and methinks that will allow the P220R to create a state of gun range Zen for its humble owner.
(0) (0) Watch Unwatch
naksukaogearreviews (verified owner) –
This is the 2nd trigger I have purchased from GG, the 1st being the P320 competition trigger kit (which is incredible). I love straight triggers but if thats not your thing there is also a curved version for you traditionalists. The P226 is an incredible pistol but the stock trigger leave much to be desired. The GG adjustable trigger changes all that. Easy to install, gets rid of all that nasty pre-travel, and with the straight trigger percieved pull weight is much better. Pair this with and SRT and a lighter mainspring and you have a trigger system to be envied! Great product and fast shipping as always.
(0) (0) Watch Unwatch
quepasakimosabe (verified owner) –
This trigger is simple to install and easy to adjust. Range time will tell how the adjustments stay set but they seem solid, especially pretravel. My used LE P229 with short reset feels like it’s a brand new gun. It makes me want to buy more products in the future.
(0) (0) Watch Unwatch
trapperjohn1975 (verified owner) –
Installed one of these triggers along with the SRT kit two years ago and to me make my P220 as good as the Sigs Legion model. I wish I could find one for my Springfield XDE it’s a nice little gun but the trigger sucks. The pre travel and reset aren’t all that good
(0) (0) Watch Unwatch